SECTION 075113 - BUILT-UP ASPHALT ROOFING
(Factory Mutual Global) insured or if using FMG requirements as quality standard. Remove [ASTM D 6222, Type I, Grade S] [ASTM D 6223 tie-offs at end of each day's work to cover exposed roofing membrane sheets and insulation with a course of coated felt set in roofing cement ... Read Document
COMPONENT SPECIFICATION TIMBER FRAMED KIT HOUSE
Sarking 9mm OSB exterior grade sheathing. Felt 22kg reinforced grade 1F or VP400 roofing membrane. Soffit Board 9.5m Far Eastern Plywood, painted as required. Ventilation Over fascia pattern. ... Read Here
Real World Maths - Home - SQA
SQA Standard Grade: General Course Project Overview Learning Areas Levels Real World Maths Constructing an Observation Deck * * * * * Real World Maths Constructing an Observation Deck * * * * * Real World Maths Project goals. What area of roofing felt will be required to clad the roof ? ... Doc Retrieval
For More Information On Hambleside Danelaw Visit Www ...
Built-up Felt Roofing with Felt Finish . . . . . . . . . . . . . . C9 Investor in People standard. Danelaw Hambleside A3 roofing grade polyester resin, incorporating a glass chopped strand mat overlaid with a glass tissue. ... Read More
Shingle Installation / Fixing Specification
Shingle Installation / Fixing Specification standard XXXXX size (the lower grade Red and Black labels contain flat grain and sapwood that makes them unsuitable A strip of roofing felt should be used beneath each capping piece. ... Read Document
Portal:United Kingdom/Featured Article - Wikipedia, The Free ...
It is the joint highest award for bravery in the United Kingdom with the George Cross, and competition from other roofing materials, the standard-issue service pistol for the armed forces of the United Kingdom, the British Empire, ... Read Article
On U Values From Domestic Heating Design Guide
And calculations based on the Standard Assessment Procedure (in the United Kingdom) or the Dwelling Energy Assessment 3 layers of felt, boarding, air space, insulation, 9.5 mm plasterboard Example room size = 6.5 x 5.0m = 11.5m exposed wall. U-value with 50mm insulation = 0.32 W/ m²K ... Read Full Source
07 52 00-26apr10 - Construction, NEWPORT CONSTRUCTION ...
Grade 2, ASTM C-1330 and ASTM D-1622, polyisocyanurate with fiberglass perforated facer sheet, 20 psi compressive strength complying with ASTM D-1621. Felt type shall provide warranty as specified in Section 07 50 00 – Paragraph 1.05, 07 52 00-26apr10.doc ... View Doc
PITCHED ROOF INSULATION AT CEILING LEVEL
PITCHED ROOF INSULATION AT CEILING LEVEL PITCHED ROOF INSULATION AT CEILING LEVEL existing on 25 x 38mm tanalised sw treated battens on sarking felt to BS747 supported on 47 x 125mm grade C24 rafters at max 600mm a Grade D category LD3 standard and to be mains powered with battery back ... Read More
Roofite Range - RIBA Product Selector
For application to roofing felt, metal, brick and construction grade plastics. Availability: 310ml cartridge. Coverage: 310ml tube would fill a crack gaps and holes. Availability: 5m x 1m also available in packs of 5 sheets. Watco Fibreglass Reinforcing Tape: Used when additional ... View Full Source
Asbestos - Wikipedia, The Free Encyclopedia
Has not included them in the asbestos standard, NIOSH and the American Thoracic Society have recommended that they be included as regulated materials. As such, Asbestos is widely used in roofing materials, but do not meet morphological requirements for commercial-grade-asbestos. ... Read Article
TIMBER FRAME - Cohaesio
Standard timber frame cavity wall with service void comprising external brickwork, membrane or roofing felt on timber rafters. 100mm rockwool roll of standard 18mm t&g flooring grade chipboard (mass per unit area ... Visit Document
Roofite Range - WATCO
Roofite® Range A range of products to repair, for application to roofing felt, metal, paint, stone, brick and construction grade plastics. Availability: 5m x 1m also available in packs of 5 sheets. Watco Fibreglass Reinforcing Tape: ... Fetch Content
The Holly, 70 Harlech Road, Abbots Langley, Herts. WD5 0BF ...
Ensure correct grade of timber is used as specified. on three layers of built up roofing felt complying with BS 747:1977(1986) laid in accordance toughened or laminated safety glazing achieving a Class C standard when tested to BS ... Fetch Full Source
Bill Of Quantities - BOS Estimating
Ref Description Quantity Units Rate Value Demolitions Complete Type `S` standard for 50 mm joists; depth: E 150 mm 30 Nr New Plasterboard Ceilings BITUMEN FELT ROOFING NOTE: We have allowed to extend the new roof ... Read Here
2 - Kerkstra Precast
Comply with camber and dimensional tolerances of PCI MNL 135, [Reglets and flashing are specified in Division 7 Section “Sheet Metal Flashing and Trim.”] felt or fiber filled. P. Accessories: Provide clips, Standard Grade: ... Document Retrieval
BEAMS SOLID FLOOR INSULATION OVER SLAB DPC
To achieve U value of 0.16 W/m²K Roofing tiles to match existing on 25 x 38mm tanalised sw treated battens on sarking felt supported on 47 x 150mm grade C16 rafters at max 400mm centres max span 0 1m 2m 3m 4m 5m SCALE RULE (1:100) 6 9 1:100 MAY 2013 CHRIS DICKMAN ... View Full Source
Planning.croydon.gov.uk
Remove flat roof coverings renew with 12.5mm chippings on 3no layers hot bonded high performance roofing felt on IBmm grade ply on 125mm Celotex TD 3125 roof insulation Achieves a U value of 0.22W/m2K. Bitumen felt proof course minimum Plunbing to British standard code of practice ... Retrieve Full Source
No comments:
Post a Comment